|
Mold Making Face Cast With 880 Alginate
Mold Making Face Cast With 880 Alginate
Lifecast mold making with 880 from Accucast. I put my shaved head to good use and did an open mouth lifecast mold with no bald cap. This is a VERY truncated version of a lifecast. [...]
|
|
Mold Making With Glove Mold Process
Mold Making With Glove Mold Process
Mold making process using a seamless glove mold made with Platsil Gel-10. This is a great process for molding simple figure sculpts or portrait busts. Gel-10 is stretchy enough to pull inside out over some basic [...]
|
|
Mold Making Techniques: Resin Mothermold Process
Mold Making Techniques: Resin Mothermold Process
Mold Making using 1512 Resin over Gel-10 silicone. 2 piece resin mother-mold created with thickened 1512 polyurethane resin.
From:
brickintheyard
Views:
9075
[...]
|
|
Mold making basics: Silicone Block Mold
Mold making basics: Silicone Block Mold
Block mold explanation. This is the most basic mold method for silicone rubber. This is a good method when speed is more important than overall cost. We used 73-45 platinum silicone for this particular mold. A [...]
|
|
Mold Making, Casting: Types of RTV Mold Rubber by Smooth-On
Mold Making, Casting: Types of RTV Mold Rubber by Smooth-On
Examining the different types of RTV mold rubber available for mold making and casting from Smooth-On
From:
SmoothOnInc
Views:
49053
[...]
|
|
Mold Making, Casting: Making Face Mold With Alginate - Smoot
Mold Making, Casting: Making Face Mold With Alginate - Smoot
Mold Making: Making a mold of a face using Alja-Safe alginate from Smooth-On. For more information, visit: www.smooth-on.com Interested in purchasing these materials? Order online at www.smoothonsecure.com Or find your nearest Smooth-On [...]
|
|
Mold Making, Casting: Brush-On Silicone Mold - 1- Smooth-On
Mold Making, Casting: Brush-On Silicone Mold - 1- Smooth-On
Part 1 of 2: Using Rebound 25 brush-on silicone rubber from Smooth-On to make a mold. For more information, visit: www.smooth-on.com Interested in purchasing these materials? Order online at www.smoothonsecure.com Or find your [...]
|
|
Mold Making, Casting: Slacker Silicone Rubber - Smooth-On
Mold Making, Casting: Slacker Silicone Rubber - Smooth-On
Using Slacker Tactile Mutator to soften or deaden platinum silicone rubber for a more lifelike feel in special effects makeup. For more information, visit: www.smooth-on.com Interested in purchasing these materials? Order online at www.smoothonsecure.com [...]
|
|
Mold Making - Mass Casting Complex Parts (w/ parting line)
Mold Making - Mass Casting Complex Parts (w/ parting line)
When mass casting a part without a flat side, you must create a two-part mold. We create a two-part silicone rubber mold with a clean parting line and then cast the part [...]
|
|
Mold Making - Making Rigid Molds With Fast-Cast Urethanes
Mold Making - Making Rigid Molds With Fast-Cast Urethanes
Ideal for smaller models/molds with a flat side, fast-cast urethanes are widely used for their ease of use, low cost, and quick demold times. However, their use requires careful application of release agents. [...]
|
